Branch Connection Fitting

Branch connections are not just tee's and lateral's, they are also weldolets.  Weldolets® are welded branch connections that are designed to match or exceed the schedule of the pipe used.  Each is marked with an outlet size and the pipe sizes that it can be welded to.  If stamped 5-3x3/4" it will have an outlet size of 3/4" and fit pipe sizes 3", 3 1/2", 4", 5" and having a maximum gap between the pipe and olet of 1/32" for the largest size.

• See Articles  -  List of Tags / List of Categories / List of Articles / List of Glossaries / Nomenclature and Symbols

If you're looking for other types of branch connections besides O'lets, click here.

Unless otherwise specified, the following trademarked names are registered to Bonney Forge.  These fittings may be available for sale under different names.  It is up to the user to ensure that the fitting meets applicable codes, such as ANSI/ASME B16.9, ANSI/ASME B16.25 or MSS SP-97.

Branch Connection Design Classification

Elbolet Branch Connection Fitting
Pipe Flange Type	Datasheets
Elbolet

Elbolet  -  An Elbolet®, abbreviared as ELO, is used on 90° long radius elbows, short radius elbows and can be used on 180° returns.  However, an Elbolet on a short radius elbow is not used often.  It typically is used for Thermowell and instrumentation connections but can be used as a drain connection when room isn't available for using a Weldolet.  The Elbolet is available with buttweld, socketweld or threaded connections.

 

Threadolet Branch Connection Fitting
Pipe Flange Type	Datasheets
Threadolet	Thredolet - Reducing and Flat, ANSI Class 3000, FCS (in)
	Thredolet - Size to Size and Flat, ANSI Class 3000, FCS (in)
	Thredolet - Reducing, ANSI Class 6000, FCS (in)

Threadolet  -  A Threadolet®, abbreviated as TOL, is the same basic design as a "weldolet."  However the main difference is the fitting has a female threaded connection to mate to the branch connection.  This makes a 90° branch and comes in full size or reducing for a straight piece of pipe.  Typically, it is in the size range of 1/2" to 2" and is welded over a hole either drilled or burned in the pipe.

 

Weldolet Branch Connection Fitting
Pipe Flange Type	Datasheets
Weldolet	Weldolet - Dimensions for Run Center to Face of Olet (in)
	Weldolet - Insert, ANSI, FCS (in)
	Weldolet - Heavy Wall, ANSI, FCS (in)
	Weldolet - Size to Size and Flat, ANSI Sch STD, FCS (in)
	Weldolet - Reducing and Flat, ANSI Sch STD, FCS (in)
	Weldolet - Size to Size and Flat, ANSI Sch XS, FCS (in)
	Weldolet - Reducing and Flat, ANSI Sch XS, FCS (in)
	Weldolet - Size to Size and Flat, ANSI Sch 160/XXS, FCS (in)
	Weldolet - Reducing and Flat, ANSI Sch 160/XXS, FCS (in)

Weldolet  -  A Weldolet®, abbreviated as WOL, makes a 90° branch connection and - comes in full size or reducing for a straight piece of pipe.  A weldolet is designated by the run length by the branch length.  For example a 6-inch weldolet on a 10-inch pipe would be a 10x6 Weldolet.  A weldolet is designed to minimize stress concentrations and provide integral reinforcement without the need for reinforcing the weld. 

Specialty Olet Design Classification

Brazolet  -  A Brazolet® is a fitting that resembles a Weldolet and is designed for use on KLM pipe (ASTM_B88) and iron pipe size ('''IPS''') brass or copper tubing. It is available with socket or threaded connections.
Coupolet  -  A Coupolet® is a fitting that is designed for use in fire protection sprinkler systems and other low pressure piping applications.  It comes with NPT female threads for 300# service.
Expanded Olet  -  A Expanded Olet® is designed to be used when the branch pipe is larger than run pipe.  It can replace the need for two fittings a tee and concentric reducer.
Flanged Olet  -  A Flanged Olet® is a combination of a Weldolet® and flange, available in classes 150 thru 2500 and any combination flange type.
Flexolet  -  A Flexolet® and Weldolet® are basically the same but with one difference.  The Flexolet® has a straight through bore and the Weldolet® has a tapered bore.
Insert Weldolet  -  A Insert Weldolet® is designed to be welded flush with the pipe and can replace a reducing tee or reinforcing plate.
Latrolet  -  A Latrolet® is similar to a Weldolet that makes a 45° reducing branch on a straight run of pipe.  End connections of a Latrolet can be buttwelded, socket welded or threaded.
Nipolet  -  A Nipolett® is a Weldolet® with a nipple and comes with either a plain or threaded end.  It's a one piece fitting that can be used for drains, vents or taps.
Sweepolet  -  A Sweepolet® is almost like a pipe saddle but has been manufactured in such a way as to minimize pipe stresses and stress concentration factors.  The weld is able to be inspected by typical weld inspection techniques such as radiography and ultrasound inspections.

• For dimensional information on the Sweepolet, view the datasheet.

How to Order

• Specify Size
  • Outlet size
  • Run or Header
• Specify Style
  • Weldolet (buttweld)
  • Thredolet (threaded)
  • Sockolet (socket)
  • Elbolet, Latrolet, Sweeploet, Insert Weldolet, Nipolet, ect.
• Indicate Class or Schedule/Pipe Wall
  • Class 3000 or 6000 - Threaded or Socket
  • STD, XS, Sch 160/XXS, ect. - Buttweld
• Select Material
  • Carbon steel
  • Stainless steel
  • Other
• Specify Design Code (if available)

Branch Connection Fitting Standards

• ASME Standards
  • ASME B16.9 - Factory-Made Wrought Buttwelding Fittings
• MSS Standards
  • MSS SP-97 - Integrally Reinforced Forged Branch Outlet Fittings - Socket Welding, Threaded, and Buttwelding End