American Gear Manufacturers Association (AGMA)

AGMA About - The American Gear Manufacturers Association is a voluntary association of companies, consultants, and academicians with a direct interest in the design, manufacture, and application of gears, couplings, and related power transmission components and equipment.

Standards

• AGMA 900-H06 - Style Manual for the Preparation of Standards, Information Sheets and Editorial Manuals
• AGMA 901-A92 - A Rational Procedure for the Preliminary Design of Minimum Volume Gears
• AGMA 904-C96 - Metric Usage
• AGMA 908-B89 - Information Sheet - Geometry Factors for Determining the Pitting Resistance and Bending Strength of Spur, Helical and Herringbone Gear Teeth
• AGMA 909-A06 - AGMA 909-A06, Specifications for Molded Plastic Gears
• AGMA 910-C90 - Formats for Fine-Pitch Gear Specification Data
• AGMA 911-A94 - Guidelines for Aerospace Gearing
• AGMA 912-A04 - Mechanisms of Gear Tooth Failure
• AGMA 913-A98 - Method for Specifying the Geometry of Spur and Helical Gears
• AGMA 914-B04 - Gear Sound Manual - Part I: Fundamentals of Sound as Related to Gears; Part II: Sources, Specifications and Levels of Gear Sound; Part III: Gear Noise Control
• AGMA 915-1-A02 - Inspection Practices - Part 1: Cylindrical Gears - Tangential Measurements
• AGMA 915-2-A05 - Inspection Practices - Part 2: Cylindrical Gears - Radial Measurements
• AGMA 915-3-A99 - Inspection Practices - Gear Blanks, Shaft Center Distance and Parallelism
• AGMA 917-B97 - Design Manual for Parallel Shaft Fine-Pitch Gearing
• AGMA 918-A93 - A Summary of Numerical Examples Demonstrating the Procedures for Calculating Geometry Factors for Spur and Helical Gears
• AGMA 920-A01 - Materials for Plastic Gears
• AGMA 922-A96 - Load Classification & Service Factors for Flexible Coupling
• AGMA 923-B05 - Metallurgical Specifications for Steel Gearing
• AGMA 925-A03 - Effect of Lubrication on Gear Surface Distress
• AGMA 926-C99 - Recommended Practice for Carburized Aerospace Gearing
• AGMA 927-A01 - Load Distribution Factors - Analytical Methods for Cylindrical Gears
• AGMA 929-A06 - Calculation of Bevel Gear Top Land and Guidance on Cutter Edge Radius
• AGMA 930-A05 - Calculated Bending Load Capacity of Powder Metallurgy (P/M)
• AGMA 932-A05 - Rating the Pitting Resistance and Bending Strength of Hypoid Gears.
• AGMA 933-B03 - Basic Gear Geometry
• AGMA 935-A05 - Recommendations Relative to the Evaluation of Radial Composite Gear Double Flank Testers
• AGMA 938-A05 - Shot Peening of Gears
• AGMA 939-A07 - Austempered Ductile Iron for Gears
• AGMA 1003-H07 - Tooth Proportions for Fine-Pitch Spur and Helical Gearing
• AGMA 1006-A97 - Tooth Proportions for Plastic Gears
• AGMA 1010-E95 - Appearance of Gear Teeth -Terminology of Wear and Failure
• AGMA 1012-G05 - Gear Nomenclature, Definitions of Terms with Symbols
• AGMA 1102-A03 - Tolerance Specification for Gear Hobs
• AGMA 1103-H07 - Tooth Proportions for Fine-Pitch Spur and Helical Gearing (Metric Edition)
• AGMA 1106-A97 - Tooth Proportions for Plastic Gears
• AGMA 2000-A88 - Gear Classification and Inspection Handbook - Tolerances and Measuring Methods for Unassembled Spur and Helical Gears (Including Metric Equivalents)
• AGMA 2001-D04 - Fundamental Rating Factors and Calculation Methods for Involute Spur and Helical Gear Teeth
• AGMA 2002-B88 - Tooth Thickness Specification and Measurement
• AGMA 2003-B97 - Rating the Pitting Resistance and Bending Strength of Generated Straight Bevel, Zerol Bevel, and Spiral Bevel Gear Teeth
• AGMA 2004-C08 - Gear Materials, Heat Treatment and Processing Manual
• AGMA 2005-D03 - Design Manual for Bevel Gears
• AGMA 2007-C00 - Surface Temper Etch Inspection After Grinding [Same as New ISO 14104]
• AGMA 2008-C01 - Assembling Bevel Gears
• AGMA 2009-B01 - Bevel Gear Classification, Tolerances, and Inspection Methods
• AGMA 2011-A98 - Cylindrical Wormgearing Tolerance and Inspection Methods
• AGMA 2015-1-A01 - Accuracy Classification System - Tangential Measurements for Cylindrical Gears
• AGMA 2015-1-A02 - Accuracy Classification System - Tangential Measurement Tolerance Tables for Cylindrical Gears
• AGMA 2015-2-A06 - Accuracy Classification System - Radial Measurements for Cylindrical Gears
• AGMA 2116-A05 - Evaluation of Double Flank Testers for Radial Composite Measurement of Gears
• AGMA 6000-B96 - Specification for Measurement of Linear Vibration on Gear Units
• AGMA 6001-D97 - Design and Selection of Components for Enclosed Gear Drives
• AGMA 6002-B93 - Design Guide for Vehicle Spur and Helical Gears
• AGMA 6006-A03 - Standard for Design and Specification of Gearboxes for Wind Turbines
• AGMA 6008-A98 - Specifications for Powder Metallurgy Gears
• AGMA 6011-I03 - Specification for High Speed Helical Gear Units
• AGMA 6013-A06 - Standard for Industrial Enclosed Gear Drives
• AGMA 6014-A06 - Gear Power Rating for Cylindrical Shell and Trunnion Supported Equipment
• AGMA 6022-C93 - Design Manual for Cylindrical Wormgearing
• AGMA 6025-D98 - Sound for Enclosed Helical, Herringbone and Spiral Bevel Gear Drives
• AGMA 6032-A94 - Standard for Marine Gear Units: Rating
• AGMA 6033-C08 - Materials for Marine Propulsion Gearing
• AGMA 6034-B92 - Practice for Enclosed Cylindrical Wormgear Speed Reducers and Gearmotors
• AGMA 6035-A02 - Design, Rating and Application of Industrial Globoidal Wormgearing
• AGMA 6113-A06 - Standard for Industrial Enclosed Gear Drives (Metric Edition)
• AGMA 6114-A06 - Gear Power Rating for Cylindrical Shell and Trunnion Supported Equipment (Metric Edition)
• AGMA 6123-B06 - Design Manual for Enclosed Epicyclic Gear Drives
• AGMA 6133-C08 - Materials for Propulsion Gearing (Metric Edition)
• AGMA 6135-A02 - Design, Rating and Application of Industrial Globoidal Wormgearing (Metric Edition)
• AGMA 6336-6-A08 - Calculation of Load Capacity of Spur and Helical Gears - Part 6: Calculation of Service Life Under Variable Load
• AGMA 9000-C90 - Flexible Couplings - Potential Unbalance Classification
• AGMA 9001-B97 - Flexible Couplings - Lubrication
• AGMA 9002-B04 - Bores and Keyways for Flexible Couplings (Inch Series)
• AGMA 9003-B08 - Flexible Couplings - Keyless Fits
• AGMA 9004-B08 - Flexible Couplings - Mass Elastic Properties and Other Characteristics
• AGMA 9005-E02 - Industrial Gear Lubrication
• AGMA 9008-B00 - Flexible Couplings - Gear Type - Flange Dimensions, Inch Series
• AGMA 9009-D02 - Flexible Couplings - Nomenclature for Flexible Couplings
• AGMA 9103-B08 - Flexible Couplings - Keyless Fits (Metric Edition)
• AGMA 9104-A06 - Flexible Couplings - Mass Elastic Properties and Other Characteristics ( Metric Edition)
• AGMA 9112-A04 - Bores and Keyways for Flexible Couplings (Metric Series)
• AGMA 10064-5-A06 - Code of Inspection Practice - Part 5: Recommendations Relative to Evaluation of Gear Measuring Instruments
• AGMA 14179-1 - Gear Reducers - Thermal Capacity Based on ISO/TR 14179-1