ASME Standards List

Tags: ASME Standards

Blanks

 

Boiler Engineering

• ASME BIO - Guide for ASME Stamp Holders for Section VIII Division 1 Vessels and the Pressure Equipment Directive
• ASME BPVC - Boiler and Pressure Vessel Code Complete Set
• ASME BPVC-I - BPVC Section I - Power Boilers
• ASME BPVC-IIA - BPVC Section II - Materials Part A - Ferrous Material Specifications
• ASME BPVC-IIB - BPVC Section II - Materials Part B - Nonferrous Material Specifications
• ASME BPVC-IIC - BPVC Section II - Materials Part C - Specifications for Welding Rods Electrodes and Filler Metals
• ASME BPVC-IID - BPVC Section II - Materials Part D - Properties-(Customary)
• ASME BPVC-II DM - Properties, Metric Version
• ASME BPVC-III-2 - BPVC Section III - Rules for Construction of Nuclear Facility Components Division 2 - Code for Concrete Containments
• ASME BPVC-III-3 - BPVC Section III - Rules for Construction of Nuclear Facility Components Div 3 - Containments for Transportation & Storage of Spent Nuclear Fuel & High Level Radioactive Mat & Waste
• ASME BPVC-III NB - BPVC Section III - Rules for Construction of Nuclear Facility Components Division 1 - Subsection NB Class 1 Components
• ASME BPVC-III NC - BPVC Section III - Rules for Construction of Nuclear Facility Components Division 1 - Subsection NC Class 2 Components
• ASME BPVC-III NCA - BPVC Section III - Rules for Construction of Nuclear Facility Components Subsection NCA - General Requirements Division 1 & 2
• ASME BPVC-III ND - Rules for Construction of Nuclear Power Plant Components - Class 3 Components
• ASME BPVC-III NE - BPVC Section III - Rules for Construction of Nuclear Facility Components Division 1 - Subsection NE Class MC Components
• ASME BPVC-III NF - BPVC Section III - Rules for Construction of Nuclear Facility Components Division 1 - Subsection NF Supports
• ASME BPVC-III NG - BPVC Section III - Rules for Construction of Nuclear Facility Components Division 1 - Subsection NG Core Support Structures
• ASME BPVC-III NH - BPVC Section III Rules for Construction of Nuclear Facility Components Division 1 - Subsection NH Class 1 Components in Elevated Temperature Service
• ASME BPVC-III APP - Rules for Construction of Nuclear Power Plant Components - Appendices
• ASME BPVC-IV - BPVC Section IV - Rules for Construction of Heating Boilers
• ASME BPVC-V - Nondestructive Examination
• ASME BPVC-VI] - Recommended Rules for Care and Operation of Heating Boilers
• ASME BPVC-VII - Recommended Guidelines for the Care of Power Boilers
• ASME BPVC-VIII-1 - Rules for Construction of Pressure Vessels
• ASME BPVC-VIII-2 - Rules for Construction of Pressure Vessels
• ASME 'BPVC-VIII-3 - Rules for Construction of Pressure Vessels - Alternative Rules for Construction of High Pressure Vessels
• ASME BPVC-IX - BPVC Section IX - Welding and Brazing Qualifications
• ASME BPVC-X - BPVC Section X - Fiber-Reinforced Plastic Pressure Vessels
• ASME BPVC-XI - BPVC Section XI - Rules for Inservice Inspection of Nuclear Power Plant Components
• ASME BPVC-XII - BPVC Section XII - Rules for Construction and Continued Service of Transport Tanks
• ASME CST-1 - Controls and Safety Devices for Automatically Fired Boilers
• ASME FFS-1 - Fitness-for-Service
• ASME HPS - High Pressure Systems
• ASME PCC-2 - Repair of Pressure Equipment and Piping
• ASME PVHO-1 - Safety Standard for Pressure Vessels for Human Occupancy
• ASME PVHO-2 - Safety Standard for Pressure Vessels for Human Occupancy: In-Service PVHO Acrylic Windows Guidelines
• ASME RTP-1 - Reinforced Thermoset Plastic Corrosion Resistant Equipment

 

Chains

• ASME B29.2M - Inverted Tooth (Silent) Chains and Sprockets
• ASME B29.8 - Leaf Chains, Clevises and Sheaves
• ASME B29.10M - Heavy Duty Offset Sidebar Power Transmission Roller Chains and Sprocket Teeth
• ASME B29.12M - Steel Bushed Rollerless Chains, Attachments and Sprocket Teeth
• ASME B29.15M - Steel Roller Type Conveyor Chains, Attachments and Sprocket Teeth
• ASME B29.17M - Hinge Type Flat Top Conveyor Chains and Sprocket Teeth
• ASME B29.21M - 700 Class Welded Steel and Case Chains, Attachments and Sprockets for Water and Sewage Treatment Plants
• ASME B29.22 - Drop Forged Rivetless Chains, Sprocket Teeth Drive Chain/Drive Dogs
• ASME B29.23M - Flexible Chain Couplings
• ASME B29.24 - Roller Load Chains for Overhead Hoists
• ASME B29.26 - Fatigue Testing Power Transmission Roller Chain
• ASME B29.27 - Single-Pitch and Double-Pitch Hollow Pin Conveyor Chains and Attachments
• ASME B29.100 - Precision Power Transmission, Double-Pitch Power Transmission and Double-Pitch Conveyor Roller Chains, Attachments and Sprockets
• ASME B29.200 - Welded-Steel-Type Mill Chains, Welded-Steel-Type Drag Chains, Attachments and Sprocket Teeth
• ASME B29.300 - Agricultural, Detachable, and Pintle Chains, Attachments and Sprockets
• ASME B29.400 - Combination - H-Type Mil Chains and Sprockets

 

Compressors

 

Conveyors

 

Cranes and Hoists

• ASME B29.24M - Roller Load Chains For Overhead Hoists
• ASME B30.1 - Jacks
• ASME B30.2 - Overhead and Gantry Cranes (Top Running Bridge, Single or Multiple Girder, Top Running Trolley Hoist)
• ASME B30.3 - Construction Tower Cranes
• ASME B30.4 - Portal, Tower, and Pedestal Cranes
• ASME B30.5 - Mobile and Locomotive Cranes
• ASME B30.6 - Derricks
• ASME B30.7 - Base-Mounted Drum Hoists
• ASME B30.8 - Floating Cranes and Floating Derricks
• ASME B30.9 - Slings
• ASME B30.10 - Hooks
• ASME B30.11 - Monorails and Underhung Cranes
• ASME B30.12 - Handling Loads Suspended from Rotorcraft
• ASME B30.13 - Storage/Retrieval (S/R) Machines and Associated Equipment
• ASME B30.14 - Side Boom Tractors
• ASME B30.16 - Overhead Hoists (Underhung)
• ASME B30.17 - Overhead and Gantry Cranes (Top Running Bridge, Single Girder, Underhung Hoist)
• ASME B30.18 - Stacker Cranes (Top or Under Running Bridge, Multiple Girder with Top or Under Running Trolley Hoist)
• ASME B30.19 - Cableways
• ASME B30.20 - Below-the-Hook Lifting Devices
• ASME B30.21 - Manually Lever Operated Hoists
• ASME B30.22 - Articulating Boom Cranes
• ASME B30.23 - Personnel Lifting Systems
• ASME B30.24 - Roller Load Chains for Overhead Hoists
• ASME B30.25 - Scrap and Material Handlers
• ASME B30.26 - Rigging Hardware
• ASME B30.27 Material Placement Systems
• ASME BTH-1 - Design of Below-the-Hook Lifting Devices
• ASME HST-1 - Performance Standard for Electric Chain Hoists
• ASME HST-2 - Performance Standard for Hand Chain Manually Operated Chain Hoists
• ASME HST-3 - Performance Standard for Manually Lever Operated Chain Hoists
• ASME HST-4 - Performance Standard for Overhead Electric Wire Rope Hoists
• ASME HST-5 - Performance Standard for Air Chain Hoists
• ASME HST-6 - Performance Standard for Air Wire Rope Hoists
• ASME NOG-1 - Rules for Construction of Overhead and Gantry Cranes (Top Running Bridge, Multiple Girder)
• ASME NUM-1 - Rules for Construction of Cranes, Monorails, and Hoists (with Bridge or Trolley or Hoist of the Underhung Type)

 

Engineering Drawings and Related Practices

• ASME B5.46 - Symbols For Machine Tool Indicator Plates
• ASME B5.51M - Preferred SI Units for Machine Tools
• ASME SI-1 - ASME Orientation and Guide for Use of SI-1 (Metric) Units
• ASME Y14.1 - Decimal Inch Drawing Sheet Size and Format
• ASME Y14.1M - Metric Drawing Sheet Size and Format
• ASME Y14.2M - Line Conventions and Lettering
• ASME Y14.3 - Multiview and Sectional View Drawings
• ASME Y14.3M - Multiview And Sectional View Drawings
• ASME Y14.4M - Pictorial Drawing
• ASME Y14.5M - Dimensioning and Tolerancing
• ASME Y14.5.1M - Mathematical Definition of Dimensioning and Tolerancing Principles
• ASME Y14.5.2 - Certification of Geometric Dimensioning and Tolerancing Professionals
• ASME Y14.6 - Screw Thread Representation
• ASME Y14.7.1 - Gear Drawing Standards-Parts 1: For Spur, Helical, Double Helical and Rack
• ASME Y14.7.2 - Gear and Spline Drawing Standards-Part 2: Bevel and Hypoid Gears
• ASME Y14.8M - Castings and Forgings
• ASME Y14.13M - Mechanical Spring Representation
• ASME 'Y14.18M - Optical Parts
• ASME Y14.24 - Types and Applications of Engineering Drawings
• ASME Y14.32.1M - Chassis Frames-Passenger Car and Light Truck-Ground Vehicle Practices
• ASME Y14.34M - Associated Lists
• ASME Y14.35M - Revision of Engineering Drawings and Associated Documents
• ASME Y14.36M - Surface Texture Symbols
• ASME Y14.38 - Abbreviations and Acronyms for Use on Drawings and Related Documents
• ASME Y14.41 - Digital Product Definition Data Practices
• ASME Y14.42 - Digital Approval Systems
• ASME Y14.43 - Dimensioning and Tolerancing Principles for Gages and Fixtures
• ASME Y14.100 - Engineering Drawing Practices
• ASME Y32.2.3 - Graphic Symbols For Pipe Fittings, Valves And Piping
• ASME Y32.2.4 - Graphic Symbols For Heating, Ventilating And Air Conditioning
• ASME Y32.4 - Graphic Symbols for Plumbing Fixtures for Diagrams Used in Architecture & Building Construction
• ASME Y32.7 - Graphics Symbols for Railroad Maps and Profiles
• ASME Y32.10 - Graphic Symbols for Fluid Power Diagrams
• ASME Y32.11 - Graphic Symbols For Process Flow Diagrams In Petroleum And Chemical Industries
• ASME Y32.18 - Symbols For Mechanical And Acoustical Elements As Used In Schematic Diagrams

 

Environmental

 

Fasteners

• ASME B18.1.1 - Small Solid Rivets
• ASME B18.1.2 - Large Rivets
• ASME B18.1.3M - Metric Small Solid Rivets
• ASME B18.2.1 - Square and Hex Bolts and Screws, Inch Series
• ASME B18.2.2 - Square and Hex Nuts
• ASME B18.2.3.1M - Metric Hex Cap Screws
• ASME B18.2.3.2M - Metric Formed Hex Screws
• ASME B18.2.3.3M - Metric Heavy Hex Screws
• ASME B18.2.3.4M - Metric Hex Flange Screws
• ASME B18.2.3.5M - Metric Hex Bolts
• ASME B18.2.3.6M - Metric Heavy Hex Bolts
• ASME B18.2.3.7M - Metric Heavy Hex Structural Bolts
• ASME B18.2.3.8M - Metric Hex Lag Screws
• ASME B18.2.3.9M - Metric Heavy Hex Flange Screws
• ASME B18.2.3.10M - Square Head Bolts, Metric Series
• ASME B18.2.4.1M - Metric Hex Nuts, Style 1
• ASME B18.2.4.2M - Metric Hex Nuts, Style 2
• ASME B18.2.4.3M - Metric Slotted Hex Nuts
• ASME B28.2.4.4M - Metric Hex Flange Nuts
• ASME B18.2.4.5M - Metric Hex Jam Nuts
• ASME B18.2.4.6M - Metric Heavy Hex Nuts
• ASME B18.2.6 - Fasteners for Use in Structural Applications
• ASME B18.2.7.1M - Metric 12-Spline Flange Screws
• ASME B18.2.8 - Clearance Holes for Bolts Screws and Studs
• ASME B18.2.9 - Straightness Gage and Gaging for Bolts and Screws
• ASME B18.3 - Socket Cap, Shoulder and Set Screws, Hex and Spline Keys, Inch Series
• ASME B18.3.1M - Socket Head Cap Screws, Metric Series
• ASME B18.3.2M - Hexagon Keys and Bits, Metric Series
• ASME B18.3.3M - Hexagon Socket Head Shoulder Screws, Metric Series
• ASME B18.3.4M - Hexagon Socket Button head Cap Screws, Metric Series
• ASME B18.3.5M - Hexagon Socket Flat Countersunk Head Cap Screws, Metric Series
• ASME B18.3.6M - Socket Set Screws, Metric Series
• ASME B18.5 - Round Head Bolts, Inch Series
• ASME B18.5.2.1M - Round Head Short Square Neck Bolts, Metric Series
• ASME B18.5.2.2M - Round Head Square Neck Bolts, Metric Series
• ASME B18.5.2.3M - Round Head Square Neck Bolts with Large Head, Metric Series
• ASME B18.6.1 - Wood Screws, Inch Series
• ASME B18.6.2 - Slotted Head Cap Screws, Square Head Set Screws and Slotted Headless Set Screws: Inch Series
• ASME B18.6.3 - Machine Screws and Machine Screw Nuts
• ASME B18.6.4 - Thread Forming and Thread Cutting Tapping Screws and Metallic
• ASME B18.6.5M - Metric Thread-Forming and Thread-Cutting Tapping Screws
• ASME B18.6.7M - Metric Machine Screws
• ASME B18.7 - General Purpose Semi-Tubular Rivets, Full Tubular Rivets, Split Rivets and Rivet Caps
• ASME B18.7.1M - Metric General Purpose Semi-Tubular Rivets
• ASME B18.8.1 - Clevis Pins and Cotter Pins, Inch Series
• ASME B18.8.2 - Taper Pins, Dowel Pins, Straight Pins, Grooved Pins, and Spring Pins, Inch Series
• ASME B18.8.100M - Spring Pins: Coiled Type; Spring Pins: Slotted; Machine Dowel Pins: Hardened Ground; and Grooved Pins, Metric Series
• ASME B18.8.200M - Cotter Pins, Headless Clevis Pins and Header Clevis Pins, Metric Series
• ASME B18.9 - Plow Bolts, Inch Series
• ASME B18.10 - Track Bolts and Nuts
• ASME B18.11 - Miniature Screws
• ASME B18.12 - Glossary of Terms for Mechanical Fasteners
• ASME B18.13 - Screw and Washer Assemblies-Sems, Inch Series
• ASME B18.13.1M - Screw and Washer Assemblies-Sems, Metric Series
• ASME B18.15 - Forged Eyebolts
• ASME B18.15M - Metric Lifting Eyes
• ASME B18.16M - Prevailing-Torque Type Steel Metric Hex Nuts and Hex Flange Nuts
• ASME B18.18.1 - Inspection and Quality Assurance for General Purpose Fasteners
• ASME B18.18.1 - Inspection and Quality Assurance for General Purpose Fasteners
• ASME B18.18.2M - Inspection and Quality Assurance for High-Volume Machine Assembly Fasteners
• ASME B18.18.2M - SUPPLEMENT (Supplement of ASME B18.18.2M) Inspection and Quality Assurance for High-Volume Machine Assembly Fasteners
• ASME B18.18.3M - Inspection and Quality Assurance for Special Purpose Fasteners
• ASME B18.18.4M - Inspection and Quality Assurance for Fasteners for Highly Specialized Engineered Applications for Metric Fasteners
• ASME B18.18.5M - Inspection and Quality Assurance Plan Requiring In-Process Inspection and Control
• ASME B18.18.6M - Quality Assurance Plan for Fasteners Produced in a Third Party Accreditation System
• ASME B18.18.7M - Quality Assurance Plan for Fasteners Produced in a Customer Approved Control Plan
• ASME B18.2.9 - Straightness Gage and Gaging for Bolts and Screws
• ASME B18.21.1 - Lock Washers, Inch Series
• ASME B18.21.2M - Lock Washers, Metric Series
• ASME B18.22.1 - Plain Washers
• ASME B18.22M - Metric Plain Washers
• ASME B18.24 - Part Identifying Number (PIN) Code System Standard for B18 Fastener Products
• ASME B18.25.1M - Square and Rectangular Keys and Keyways
• ASME B18.25.2M - Woodruff Keys and Keyways
• ASME B18.25.3M - Square and Rectangular Keys and Keyways: Width Tolerances and Deviations Greater than Basic Size
• ASME B18.27 - Tapered and Reduced Cross Section Retaining Rings, Inch Series
• ASME B18.29.1 - Helical Coil Screw Thread Inserts - Free Running and Screw Locking, Inch Series
• ASME B18.29.2M - Helical Coil Screw Thread Inserts - Free Running and Screw Locking, Metric Series
• ASME B18.30.1M - Open-End Blind Rivets with Break Mandrels, Metric Series
• ASME B18.31.1M - Metric Continuous and Double End Studs

 

Fittings, Flanges & Gaskets

• ASME B16.1 - Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250
• ASME B16.3 - Malleable Iron Threaded Fittings: Classes 150 and 300
• ASME B16.4 - Gray Iron Threaded Fittings: (Classes 125 and 250)
• ASME B16.5 - Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard
• ASME B16.9 - Factory-Made Wrought Buttwelding Fittings
• ASME B16.10 - Face to Face and End to End Dimensions of Valves
• ASME B16.11 - Forged Fittings, Socket-Welding and Threaded
• ASME B16.12 - Cast Iron Threaded Drainage Fittings
• ASME B16.14 - Ferrous Pipe Plugs, Bushings and Locknuts with Pipe Threads
• ASME B16.15 - Cast Copper Alloy Threaded Fittings: Classes 125 and 250
• ASME B16.18 - Cast Copper Alloy Solder Joint Pressure Fittings
• ASME B16.20 - Metallic Gaskets for Pipe Flanges: Ring-Joint, Spiral-Wound, and Jacketed
• ASME B16.21 - Nonmetallic Flat Gaskets for Pipe Flanges
• ASME B16.22 - Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
• ASME B16.23 - Cast Copper Alloy Solder Joint Drainage Fittings: DWV
• ASME B16.24 - Cast Copper Alloy Pipe Flanges and Flanged Fittings: Classes 150, 300, 600, 900, 1500 and 2500
• ASME B16.25 - Buttwelding Ends
• ASME B16.26 - Cast Copper Alloy Fittings for Flared Copper Tubes
• ASME B16.28 - Wrought Steel Buttwelding Short Radius Elbows and Returns
• ASME B16.29 - Wrought Copper and Wrought Copper Alloy Solder-Joint Drainage Fittings-DWV
• ASME B16.33 - Manually Operated Metallic Gas Valves for use in Gas Piping Systems up to 125 psi (Sizes NPS 1/2 - NPS 2)
• ASME B16.34 - Valves Flanged, Threaded and Welding End
• ASME B16.36 - Orifice Flanges
• ASME B16.38 - Large Metallic Valves for Gas Distribution: Manual Operated,NPS 2 1/2 (DN 65) to NPS 12 (DN 300), 125 psig (8.6 bar) Maximum
• ASME B16.39 - Malleable Iron Threaded Pipe Unions: Classes 150, 250, and 300
• ASME B16.40 - Manually Operated Thermoplastic Gas Shutoffs and Valves in Gas Distribution Systems
• ASME B16.42 - Ductile Iron Pipe Flanges and Flanged Fittings: Classes 150 and 300
• ASME B16.44 - Manually Operated Metallic Gas Valves for use in Above Ground Piping Systems up to 5 psi
• ASME B16.45 - Cast Iron Fittings for Sovent Drainage Systems
• ASME B16.47 - Large Diameter Steel Flanges: NPS 26 Through NPS 60 Metric/Inch Standard
• ASME B16.48 - Line Blanks
• ASME B16.49 - Factory-Made, Wrought Steel, Buttwelding Induction Bends for Transportation and Distribution Systems
• ASME B16.50 - Wrought Copper and Copper Alloy Braze-Joint Pressure Fittings
• ASME PCC-1 - Guidelines for Pressure Boundary Bolted Flange Joint Assembly
• ASME Y32.2.3 - Graphic Symbols for Pipe Fittings, Valves And Piping

 

Gauges & Gaging

 

Keys & Keyseats

• ASME B17.1 - Keys and Keyseats
• ASME B17.2 - Woodruff Keys and Keyseats
• ASME B18.25.1M - Square and Rectangular Keys and Keyways
• ASME B18.25.2M - Woodruff Keys and Keyways (Metric)
• ASME B18.25.3M - Square and Rectangular Keys and Keyways: Width Tolerances and Deviations Greater than Basic Size (Metric)

 

Lifts

 

Limits and Fits

 

Measurement

• ASME B40.100 - Pressure Gauges and Gauge Attachments
• ASME B40.200 - Thermometers, Direct Reading and Remote Reading
• ASME B89.1.2M - Calibration of Gage Blocks by Contact Comparison Methods (Through 20 in. and 500 mm)
• ASME B89.1.5 - Measurement of Plain External Diameters for Use as Master Discs or Cylindrical Plug Gages
• ASME B89.1.6 - Measurement of Plain Internal Diameters for use as Master Rings or Ring Gages
• ASME B89.1.9 - Gage Blocks
• ASME B89.1.10M - Dial Indicators (for Linear Measurements)
• ASME B89.1.13 - Micrometers
• ASME B89.1.17 - Measurement of Thread Measuring Wires
• ASME B89.3.1 - Measurement of Out-of-Roundness
• ASME B89.3.4M - Axes of Rotation - Methods for Specifying and Testing
• ASME B89.4.1 - Methods for Performance Evaluation of Coordinate Measuring Machines (CMM)
• ASME B89.4.10 - Methods for Performance Evaluation of Coordinate Measuring Systems Software
• ASME B89.4.19 - Performance Evaluation of Laser-Based Spherical Coordinate Measurement Systems
• ASME B89.4.22 - Methods for Performance Evaluation of Articulated Arm Coordinate Measuring Machines (CMM)
• ASME B89.6.2 - Temperature and Humidity Environment for Dimensional Measurement
• ASME B89.7.2 - Dimensional Measurement Planning
• ASME B89.7.3.1 - Guidelines for Decision Rules: Considering Measurement Uncertainty in Determining Conformance to Specifications
• ASME B89.7.3.2 - Guidelines for the Evaluation of Dimensional Measurement Uncertainty
• ASME B89.7.3.3 - Guidelines for Assessing the Reliability of Dimensional Measurement Uncertainty Statements
• ASME B89.7.4.1 - Measurement Uncertainty and Conformance Testing: Risk Analysis
• ASME B89.7.5 - Metrological Traceability of Dimensional Measurements to the SI Unit of Length
• ASME B89 TECH PAPER - Space Plate Test Recommendations for Coordinate Measuring Machines (CMM‚Äôs)
• ASME B89 TECH REPORT - RPT Parametric Calibration of Coordinate Measuring Machines (CMM‚Äôs)
• ASME MFC-1M - Glossary of Terms Used in the Measurement of Fluid Flow in Pipes
• ASME MFC-2M - Measurement Uncertainty for Fluid Flow in Closed Conduits
• ASME MFC-3M - Measurement of Fluid Flow in Pipes Using Orifice, Nozzle and Venturi
• ASME MFC-4M - Measurement of Gas Flow by Turbine Meters
• ASME MFC-5M - Measurement of Liquid Flow in Closed Conduits Using Transit-Time Ultrasonic Flowmeters
• ASME MFC-6M - Measurement of Fluid Flow in Pipes Using Vortex Flowmeters
• ASME MFC-7M - Measurement of Gas Flow by Means of Critical Flow Venturi Nozzles
• ASME MFC-8M - Fluid Flow in Closed Conduits: Connections for Pressure Signal Transmissions Between Primary and Secondary Devices
• ASME MFC-9M - Measurement of Liquid Flow in Closed Conduits by Weighing Methods
• ASME MFC-10M - Method for Establishing Installation Effects on Flowmeters
• ASME MFC-11 - Measurement of Fluid Flow by Means of Coriolis Mass Flowmeters
• ASME MFC-12M - Measurement of Fluid Flow in Closed Conduits Using Multiport Averaging Pitot Primary Elements
• ASME MFC-13M - Measurement of Fluid Flow in Closed Conduits: Tracer Methods
• ASME MFC-14M - Measurement of Fluid Flow Using Small Bore Precision Orifice Meters
• ASME MFC-16 - Measurement of Liquid Flow in Closed Conduits With Electromagnetic Flowmeters
• ASME MFC-18M - Measurement of Fluid Flow Using Variable Area Meters
• ASME MFC-22 - Measurement of Liquid by Turbine Flowmeters
• ASME PTC 19.2 - Pressure Measurement
• ASME PTC 19.3 TW - Thermowells
• ASME PTC 19.5 - Flow Measurement

 

Nuclear

• ASME AG-1 - Code on Nuclear Air and Gas Treatment
• ASME N278.1 - Self-Operated and Power-Operated Safety-Related Valves Functional Specification Standard
• ASME N509 - Nuclear Power Plant Air-Cleaning Units and Components
• ASME N510 - Testing of Nuclear Air Treatment Systems
• ASME NOG-1 - Rules for Construction of Overhead and Gantry Cranes (Top Running Bridge, Multiple Girder)
• ASME NQA - TECH RPT Comparison of ASME NQA-1 and ISO 9001.
• ASME NQA-1 - Quality Assurance Requirements for Nuclear Facility Applications (QA)
• ASME NUM-1 - Rules for Construction of Cranes, Monorails and Hoists (with Bridge or Trolley or Hoist of the Underhung Type)
• ASME OM - Code for Operation and Maintenance of Nuclear Power Plants
• ASME OM-S/G - Standards and Guides for Operation and Maintenance of Nuclear Power Plants
• ASME QME-1 - Qualification of Active Mechanical Equipment Used in Nuclear Power Plants
• ASME RA-S - Standard for Probabilistic Risk Assessment for Nuclear Power Plant Applications

 

Pipeline and Piping

• ASME A31.1 - Scheme for the Identification of Piping Systems
• ASME B31.1 - Power Piping
• ASME B31.2 - Fuel Gas Piping
• ASME B31.3 - Process Piping
• ASME B31.4 - Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids
• ASME B31.5 - Refrigeration Piping and Heat Transfer Components
• ASME B31.8 - Gas Transmission and Distribution Piping Systems
• ASME B31.8S - Managing System Integrity of Gas Pipelines
• ASME B31.9 - Building Services Piping
• ASME B31.11 - Slurry Transportation Piping Systems
• ASME B31.12 - Hydrogen Piping and Pipelines
• ASME B31E - Standard for the Seismic Design and Retrofit of Above-Ground Piping Systems
• ASME B31G - Manual for Determining the Remaining Strength of Corroded Pipelines: Supplement to ASME B31 Code for Pressure Piping
• ASME B31J - Standard Test Method for Determining Stress Intensification Factors (i-Factors) for Metallic Piping Components
• ASME B31Q - Pipeline Personnel Qualification
• ASME B36.10M - Welded and Seamless Wroth Steel Pipe
• ASME B36.19M - Stainless Steel Pipe

 

Pressure Vessels

 

Plumbing

• ASME A112.1.2 - Air Gaps in Plumbing Systems (For Plumbing Fixtures and Water-Connected Receptors)
• ASME A112.1.3 - Air Gap Fittings for Use with Plumbing Fixtures, Appliances and Appurtenances
• ASME A112.3.1 - Performance Standard and Installation Procedures for Stainless Steel Drainage System for Sanitary, Storm and Chemical Applications, Above and Below Ground
• ASME A112.3.4 - Macerating Toilet Systems and Related Components
• ASME A112.4.1 - Water Heater Relief Valve Drain Tubes
• ASME A112.4.2 - Water Closet Personal Hygiene Devices
• ASME A112.4.3 - Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System
• ASME A112.4.7 - Point of Use and Branch Water Submetering Systems
• ASME A112.4.14 - Manually Operated, Quarter-Turn Shutoff Valves for Use in Plumbing Systems
• ASME A112.6.1M - Floor-Affixed Supports for Off-the-Floor Plumbing Fixtures for Public Use
• ASME A112.6.2 - Framing-Affixed Supports for Off-the-Floor Water Closets with Concealed Tanks
• ASME A112.6.3 - Floor Drains and Trench Drains
• ASME A112.6.4 - Roof, Deck and Balcony Drains
• ASME A112.6.7 - Enameled and Epoxy Coated Cast Iron and PVC Plastic Sanitary Floor Sinks
• ASME A112.6.9 - Siphonic Roof Drains
• ASME A112.14.1 - Backwater Valves
• ASME A112.14.3 - Grease Interceptors
• ASME A112.14.4 - Grease Removal Devices
• ASME A112.14.6 - FOG (Fats, Oils and Greases) Disposal Systems
• ASME A112.18.1 - Plumbing Supply Fittings
• ASME A112.18.2 - Plumbing Waste Fittings
• ASME A112.18.3 - Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings
• ASME A112.18.6 - Flexible Water Connectors
• ASME A112.18.7 - Deck Mounted Bath/Shower Transfer Valves with Integral Backflow Protection
• ASME A112.19.1M - Enameled Cast Iron Plumbing Fixtures
• ASME A112.19.2 - Vitreous China Plumbing Fixtures and Hydraulic Requirements for Water Closets and Urinals
• ASME A112.19.3 - Stainless Steel Plumbing Fixtures (Designed for Residential Use)
• ASME A112.19.4M - Porcelain Enameled Formed Steel Plumbing Fixtures
• ASME A112.19.5 - Trim for Water-Closet Bowls, Tanks and Urinals
• ASME A112.19.6 - Hydraulic Performance Requirements for Water Closets and Urinals
• ASME A112.19.7 - Hydromasssage Bathtub Appliances - Suction Fittings for Use in Swimming Pools, Wading Pools, Spas and Hot Tubs
• ASME A112.19.9M - Non-Vitreous Ceramic Plumbing Fixtures
• ASME A112.19.10 - Dual Flush Devices for Water Closets
• ASME A112.19.12 - Wall Mounted, Pedestal Mounted, Adjustable, Elevating, Tilting, and Pivoting Lavatory, Sink, and Shampoo Bowl Carrier Systems and Drain Waste Systems
• ASME A112.19.13 - Electrohydraulic Water Closets
• ASME A112.19.14 - Six-Liter Water Closets Equipped with a Dual Flushing Device
• ASME A112.19.15 - Bathtubs/Whirlpool Bathtubs with Pressure Sealed Doors
• ASME A112.19.16 - Terrazzo Plumbing Fixtures
• ASME A112.19.17 - Manufactured Safety Vacuum Release Systems (SVRS) for Residential and Commercial Swimming Pool, Spa, Hot Tub, and Wading Pool Suction Systems
• ASME A112.19.19 - Vitreous China Nonwater Urinals
• ASME A112.20.1 - Qualification of Installers of High Purity Piping Systems
• ASME A112.20.2 - Qualification of Installers of Firestop Systems and Devices For Piping Systems
• ASME A112.21.3M - Hydrants for Utility and Maintenance Use
• ASME A112.36.2M - Cleanouts
• ASME B31.9 - Building Services Piping

 

Pumps

• ASME B73.1 - Specification for Horizontal End Suction Centrifugal Pumps for Chemical Process
• ASME B73.1M - Specification For Horizontal End Suction Centrifugal Pumps For Chemical Process
• ASME B73.2 - Specifications for Vertical In-Line Centrifugal Pumps for Chemical Process
• ASME B73.3- Specification for Sealless Horizontal End Suction Metallic Centrifugal Pumps for Chemical Process
• ASME B73.5M - Thermoplastic/Thermoset Polymer Material Horizontal End Suction Centrifugal Pumps Chemical Process
• ASME PTC 8.2 - Centrifugal Pumps
• ASME PTC 9 - Displacement Compressors, Vacuum Pumps And Blowers
• ASME PTC 18 - Hydraulic Turbines and Pump-Turbines

 

Screw Threads

• ASME B1.1 - Unified Inch Screw Threads, (UN and UNR Thread Form)
• ASME B1.2 - Gages and Gaging for Unified Inch Screw Threads
• ASME B1.3 - Screw Thread Gaging Systems for Acceptability: Inch and Metric Screw Threads (UN, UNR, UNJ, M, and MJ)
• ASME B1.3M - Screw Thread Gaging Systems for Dimensional Acceptability - Inch and Metric Screw Threads (UN, UNR, UNJ, M and MJ).
• ASME B1.5 - Acme Screw Threads
• ASME B1.7 - Screw Threads: Nomenclature, Definitions, and Letter Symbols
• ASME B1.8 - Stub Acme Screw Threads
• ASME B1.9 - Buttress Inch Screw Threads (7 Degree/45 Degree Form with 0.5 Pitch Basic Height of Thread Engagement)
• ASME B1.10M - Unified Miniature Screw Threads
• ASME B1.11 - Microscope Objective Thread
• ASME B1.12 - Class 5 Interference-Fit Thread
• ASME B1.13M - Metric Screw Threads: M Profile
• ASME B1.15 - Unified Inch Screw Threads, (UNJ Thread Form)
• ASME B1.16M - Gages and Gaging for Metric M Screw Threads
• ASME B1.20.1 - Pipe Threads, General Purpose, Inch
• ASME B1.20.2M - Pipe Threads, 60 Degree, General Purpose
• ASME B1.20.3 - Dryseal Pipe Threads, Inch
• ASME B1.20.5 - Gaging for Dryseal Pipe Threads-Inch
• ASME B1.20.7 - Hose Coupling Screw Threads (Inch)
• ASME B1.21M - Metric Screw Threads: MJ Profile
• ASME B1.22M - Gages and Gaging for MJ Metric Screw Threads
• ASME B1.30 - Screw Threads: Standard Practice for Calculating and Rounding Dimensions
• ASME B1 - Technical Report Measurement Uncertainty for 60 Degree Screw Thread Gage Element Measurement (Inch and Metric)
• ASME B47.1 - Gage Blanks
• ASME B94.9 - Taps: Ground and Cut Threads (Inch and Metric Sizes)
• ASME Y14.6 - Screw Thread Representation

 

Steel Stacks

 

Storage Tanks

 

Turbines

• ASME PTC 4 - Fired Steam Generators
• ASME PTC 4.4 - Gas Turbine Heat Recovery Steam Generators
• ASME PTC 6 - Steam Turbines
• ASME PTC 6.2 - Steam Turbines in Combined Cycles
• ASME PTC 6 REPORT - Guidance for Evaluation of Measurement Uncertainty in Performance Tests of Steam Turbines
• ASME PTC 6A - Appendix A to PTC6, the Test Code for Steam Turbines
• ASME PTC 6S REPORT - Procedures for Routine Performance Tests of Steam Turbines
• ASME PTC 8.2 - Centrifugal Pumps
• ASME PTC 18 - Hydraulic Turbines and Pump-Turbines
• ASME PTC 22 - Performance Test Codes on Gas Turbines
• ASME PTC 25 - Pressure Relief Devices
• ASME PTC 29 - Speed-Governing Systems for Hydraulic Turbine-Generator Units
• ASME 'PTC 42 - Wind Turbines
• ASME PTC 47 - Integrated Gasification Combined Cycle Power Generation Plants
• ASME TDP-1 - Recommended Practices for the Prevention of Water Damage to Steam Turbines used for Electric Power Generation: Fossil-Fuel Plants

 

Valves

• ASME A112.4.14 - Manually Operated, Quarter-Turn Shutoff Valves for Use in Plumbing Systems
• ASME A112.14.1 - Backwater Valves
• ASME A112.18.7 - Deck Mounted Bath/Shower Transfer Valves with integral Backflow Protection
• ASME B16.10 - Face-to-Face and End-to-End Dimensions of Valves
• ASME B16.33 - Manually Operated Metallic Gas Valves for Use in Gas Piping Systems up to 125 psi (Sizes NPS 1/2 ‚Äì NPS 2)
• ASME B16.34 - Valves - Flanged, Threaded and Welding End
• ASME B16.38 - Large Metallic Valves for Gas Distribution: Manual Operated, NPS 2 1/2 (DN 65) to NPS 12 (DN 300), 125 psig (8.6 bar) Maximum
• ASME B16.40 - Manually Operated Thermoplastic Gas Shutoffs and Valves in Gas Distribution Systems
• ASME B16.44 - Manually Operated Metallic Gas Valves for Use in Aboveground Piping Systems up to 5 psi
• ASME N278.1 - Self-Operated and Power-Operated Safety-Related Valves Functional Specification Standard
• ASME OM CODE - Code for Operation and Maintenance of Nuclear Power Plants
• ASME OM-S/G - Standards and Guides for Operation and Maintenance of Nuclear Power Plants
• ASME PCT 25 - Pressure Relief Devices
• ASME QME-1 - Qualification of Active Mechanical Equipment Used in Nuclear Power Plants

 

Water Management

 

Welding & Brazing